How Do I Clean a Clogged Drain Tile (2024)

To unclog a draintile choose the right draincleaner for thejob.

1. Consider using a sewer jetter to clean and remove dirt, sand, and yard debris that clog the foundation perimeter draintile outside yourhome.
   • A sewer jetter that's powered by your pressure washer can help you flush away the silt and debris so fewer clogs comeback.
   • A Needle Nose™ drain cleaner is a sewer jetter with a tougher, braided steel jacket and a special compact nozzle tip that allows it to pass through more types and sizes ofdrains.
   • Powering the sewer jetter with a gas pressure washer rated 2.0GPM to 4.0GPM can make the job much easier, since outdoor silt and debris can take significant force to scrub and flush out of theline.
   • Electric pressure washers are not recommended for cleaning drain tiles unless the clog consists of easily flushed material that is less than 25 feet from the bottom opening.
   • Before you start the job, find one or more drain openings that are downhill from the clog. Start from the downhill opening and clean in an uphill direction to help give the sediment a path to exit thedrain.
   • Note: you should avoid using a sewer jetter in these cases:
   • If you have a non-cylindrical basem*nt waterproofing drain tile, sold as WaterGuard, SealOnce and other brands, the design usually has rectangular corners that block sewerjetters and other drain cleaners. If you have a clogged drain tile that does not have a round cross-section, contact the installer for help to service or replace the draintile.
   • If you think that the clog could be caused by tree roots, and you're sure that the drain is in good physical condition, consider renting a large mechanical drum auger with a root cutting blade to clear theline.
   • If you think that the drain tile could have sections that are separated or collapsed, or if it is made of ceramic material (clay or concrete), you should inspect the drain tile with a video camera to make sure there's no large crack or damaged section where a sewer jetter or mechanical snake might get stuck.
2. To clean your drain tile with a sewerjetter:
   • Put on fluid resistant work gloves and eyeprotection.
   • Connect the drain cleaner to your trigger gun, start the pressure washer, and then guide the nozzle at least a foot into the drain tile opening, taking care to feed the nozzle in the direction of the clog, before you start the flow of water.
   • Guide the sewer jetter into the drain tile as you squeeze the trigger. For more thorough cleaning, every few feet pull back about halfway and then continue movingforward.
   • After you have finished cleaning the drain tile, pull the drain cleaner out. Use care to release the trigger to stop the flow of water before the nozzle reaches the drain opening. Then replace any drain cover.
   • For more details you can watch this 3minute video.
3. If you're not comfortable performing any of these steps, hiring a waterproofing service company could save you money in the long run. To find a service company in yourarea:
   • Start by asking family, friends and co-workers to recommend a company that has performed similar services forthem.
   • If you are unable to find a good recommendation from someone you know, search local directories like Google Maps, Yelp and CitySearch for waterproofing service companies nearby who have good online reviews. Don't always trust reviews from individuals who published very few other reviews, or from people who give only positive reviews to everyone. Be aware that good service companies sometimes get a small number of negative reviews for reasons that might not be relevant to your situation. Look for a company with several reviews that tell a positive, believable story about services that are similar toyours.
   • After you find one or more service companies that seem to have a good reputation, search online for the company name and the names of individuals at the company, if known. Take into account both the positive and negative information that you find about thecompany.
   • Be aware that good service companies sometimes have a backlog of several days during peak times when there are low temperatures, heavy rainfall or holidays. Sometimes heavy demand can be a sign of a company with lots of repeatcustomers.

If you have questions or comments please contact us.